[stag] Stag Digest Advertisers: regular posting
For information on how to support the stag-digest with advertising, contact Richard Welty, rwelty@krusty-motorsports.com If you are a subscriber who wishes to help support the list, contributions may...
View ArticleRe: [stag] Soft top fitting
Stuart, I just replaced my soft top a few months ago so my memory is still quite clear. Yes, the top header is glued as well. This is important so when you stretch the material it will stick to the...
View ArticleRe: Side impact bars.
Hi Sujit, Side Impact Bars were required by Federal Safety Specification no later than 1 January 1973 manufacture date. Many other auto manufacturers had them installed years earlier. Stag Side Impact...
View Article[stag] removing diff flanges
Will these come off with a simple 3 jaw puller? I don't want to bend them. I haven't tried yet, but thought I'd check with the list. Sujit
View ArticleRe: [stag] removing diff flanges
Sujit, The Flange is attached to the Quill Shaft by a nut on a taper. The Quill shaft rides on its own bearing inside the suspension frame. Typically once you remove the nut and washer, a few light...
View ArticleRe: [stag] Soft top fitting
Stuart, The stuff under the hood fabric between the fabric and header rail is more like a cork material. It should be replaced because it crumbles to cheese, but I would recommend a closed cell foam...
View ArticleRe: [stag] removing diff flanges
Sujt, You are talking about the diff flange on the prop shaft? Wheel Bearing Flanges are way different and need a special Churchill tool. You will break a 3 jaw puller and bend the wheel flanges if...
View ArticleRe: [stag] removing diff flanges
Hello Glenn,I need to remove the flanges on the diff which attach to the half-shafts. Sujit From: StagByTriumph <EmailWitheld> To: stag@digest.net Sent: Monday, August 24, 2015 7:04 PM Subject:...
View Article[stag] Completely Rebuilt Stag Engine
I'm selling a totally rebuilt 1973 Stag engine Heads: All new guides, seats, springs, valves. Heads milled .010 for flatness, block reassembled with thicker gaskets to preserve intake manifold bolt...
View ArticleClik here to view.
Trophy
Well you all know how challenging it can be to keep these beasts on the road. Been rebuilding the brake system and working on the front calipers. Typical you get so far and then the brick wall time to...
View Article[stag] Soft top fitting
Thanks I take the point that sticking the soft top to the top of the header rail will allow me to position the soft top as , from what I have read, there seems to be a lot of pulling and tugging...
View Article[stag] Re: stag-digest V4 #4451
Sujit, If it is the side flanges to replace the side diff oil seals then yes, flanges very hard to remove. B I had access to a 40 ton hydraulic press and the flange would not separate from the shaft....
View Article[stag] Stag Digest Advertisers: regular posting
For information on how to support the stag-digest with advertising, contact Richard Welty, rwelty@krusty-motorsports.com If you are a subscriber who wishes to help support the list, contributions may...
View Article[stag] is http://www.socspares.co.uk/ alive?
Sent a few emails but didn't get a reply. Sujit
View Article[stag] Rebuilt Stag OHC V-8 On eBay
Here's a link to my rebuilt Stag engine on eBay. [www.ebay.com] Plenty of pictures in the listing. This is a GREAT engine. Someone must need it. Thanks, Rich Treutt
View ArticleLooking for tonneau release handle 814067
Hi Does anyone in the US have a tonneau release handle part # 814067 to sell? This is the chrome die cast release handle on the left B pillar. If you have one you would like to sell, please contact me...
View Article[stag] Need to remove differential side input shaft flange
Can I simply remove the 4 bolts from the housing of the side input shafts of the diff. to remove the shaft? I need to have someone remove the flanges from the side input shafts as I don't have a...
View ArticleClutch hydraulics
What's going on? I can't build any resistance in my clutch pedal. Both cylinders are new, as is the hose. I just completely dissasembled both master and slave and all seems to be well. I bench bled...
View ArticleRe: [stag] Clutch hydraulics
Open the bleed valve with a hose attached running into a glass and pump away. Something will come out. If not....ensure the MC is attached to the pedal....:) Sent from my iPhone > On Aug 31, 2015,...
View ArticleRe: [stag] Clutch hydraulics
Oh and check for hydraulic fluid coming out the back of the MC. That's not good obviously. Sent from my iPhone > On Aug 31, 2015, at 8:03 PM, leejohn7 <EmailWitheld> wrote: > >...
View Article
